How to Find Your IMEI Number (Alarm.com Panels)
To move your alarm monitoring to Canadian Smart Systems we need the ID of your panel's cellular radio. Type it into our IMEI checker and we will tell you right away whether it is ready to activate. Most Alarm.com systems use a 15-digit IMEI. Older DSC and Honeywell Vista modules use a 10-digit Alarm.com serial number.
Before you start
Type digits only. Leave out spaces and dashes.
Take a photo of the screen or label instead of copying the number by hand. One wrong digit shows as "not found".
Not these numbers: the SIM card number (ICCID, usually 19 to 20 digits), the IMSI, a MAC address (it contains letters), or the panel's own hardware serial number.
Qolsys IQ Panel 2, IQ Panel 2 Plus, IQ Panel 4 and IQ Panel 5
Swipe down from the top of the home screen.
Tap Settings, then Advanced Settings.
Enter your master code (the installer or dealer code also works).
Tap About, then Cellular.
Find the line labelled IMEI and write down all 15 digits. Ignore the IMSI and ICCID lines.
No code? The IMEI is also printed on a label on the back of the panel and on the side of the original box.
2GIG GC3 and GC3e
These panels use a plug-in cellular radio in a bay on the left side. On the touchscreen, open the installer menu, then Installer Toolbox, then Radio Status. The 15-digit Serial Number shown there is the number we need. Menus can differ between software versions, so if yours looks different, read the sticker on the radio itself (power the panel down first). It may be labelled IMEI or ADC.
2GIG GC2
Tap the 2GIG logo in the bottom-right corner, enter the installer code, then tap Radio Status. Use the 15-digit Serial Number. Without the code, the number is on a sticker on the cell card inside the panel.
2GIG Edge
Tap the 2GIG logo in the upper-right corner, then System Info, and find the line labelled IMEI. The same number is on the label on the back plate and on the box.
DSC PowerSeries Neo and PowerSeries with an Alarm.com module
On an LCD keypad, press and hold [1] for about 10 seconds. The keypad shows the 10-digit Alarm.com serial number. You can also open the communicator or module and read the number after SN/IMEI on its sticker.
Honeywell Vista with an Alarm.com module
Open the alarm cabinet and find the Alarm.com radio board. Its sticker reads something like "SN/IMEI: 88888 - 1234567890". Enter the 10 digits after the dash.
Panels that cannot be checked here
Some brands are not Alarm.com systems, so the checker will not recognise them: Honeywell/Resideo ProA7 and ProA7Plus, Lyric and Lynx panels, DSC Connect 24 communicators, and Telguard units. They use other monitoring services. Call us on 647-931-2277 and we will tell you your options.
Cannot get to the panel?
Look on the original box and on your installation paperwork or invoice.
Ask your previous alarm company for the Alarm.com serial number or IMEI. They can see it in their dealer portal.
Call us and tell us the brand and model printed on the front of the panel. We will walk you through it.
If your system has an older 3G radio
Canada's 3G cellular networks are being shut down. Rogers began retiring its 3G network in August 2025, and Bell and Telus have announced a national shutdown date of March 1, 2027. An alarm radio that only works on 3G stops sending signals once its area is switched off, so it needs an LTE upgrade. Many panels only need a new radio, not a new system. Ask us for a quote.
What your result means
Available: the radio is free to activate with us.
Registered to another dealer: only one dealer can hold a radio at a time. Ask your current or previous company to close the Alarm.com account and release it, then check again.
3G or not supported: the radio needs an LTE upgrade.
Not found or invalid: re-check the digits against your photo, or call us.
Ready? Check your IMEI now, or call 647-931-2277 and we will do it with you.



Comments